12ga,10ga,8ga,4ga FH; 585HE/700HE; Big Bores--

[hubel585]

Here is good simple system with big hollowbase slugs to stop
the skirts from deforming, I found that dense dow foam works
good, I was using glue gun but dow foam is easier, Just cut
plugs out of foam sheet and force into the base. Make a tight
fit, use spot of glue inside, glue that is for foam....
Trim off the foam flush..In picture is 10 ga 900gr slug.

How we get good 24ga plastic seals with protusion on
top that fits up inside 58cal Minie base, same bore as 24ga
and our 585HE. I get the 24ga seal by cutting apart the BPI
24ga Brush wad, getting two seals out of each.Works great
in plastic case giving a shorter column than other seals and
wads, so we can get in enough of our 4759 for good speed.
The 24ga idea is getting nicer all the time with
the variety of cheap 58cal slugs, and good 3" brass cases,
drawn cases, we didn't have to wait to get made.
And all kind of guns we can use, bolt 395 Mossbergs, single
shots of all kinds, Autos,, pumps. bolt action Savage,
even 1887 Win and Greener MKIII, bolt action JC Higgins. .

Here is picture Khan auto we setting up 24ga FH, it is 3.5"
model, has a 12ga barrel to change with. Being 3.5" it
feeds/ejects through lengthened port 3" brass 24ga cases we
made from 577NE brass. We rework back of the bolt for
slightly longer stroke.Ed

　
　
　

 

[40Arpent]

Where is all of this going? Three years of experimentation....has anything made it into the market yet?

 

[bigbigtex]

This just be what the Terminator carries in the next film. LOL

 

[hubel585]

Been 10 years, lots of info for guys who reload, got a good 12ga sabot setup that guys can reload with..

Got 585 He cartridge being made in volumne
barrels in volumn, guys getting guns built around the world

Here is picture of 24ga cases, loads; and some slugs and seals.
Brass cases are 3", plastic cases are 2.5". Brass 3" can be loaded
to match 577NE power.

Here is of 24ga in an 87 Win, just test gun of mine. Uses same barrels
as our 585HE, This one has slow twist for Minie bullets.Our guys
have got supply of regular and slow twist barrels.

Here is picture of the first 585HE done and shooting in Australia.
It is owned by the poster, 'tankhunter' on the AR forums.
Built by his smith who has a reamer.
Guys there can get cases from Bertram, and there will soon be three
reamers there. There is a company there now making 585 barrels,
Allan and Grant Swan. in Redbank, Queensland.....Ed

　

 

[hubel585]

Finally got back to forums.Been busy with 24ga FH and 585HE
and getting 585 cases made, as many as possible...
We are now working a bit with 24ga FH and here is picture
of it with our 585HE case. Both use same bullets/slugs, same
bore barrels. Main use difference, 24ga FH easy setup in break
actions and 585HE in bolt actions and falling blocks.

Picture of non-discarding 585/24ga sabot cup I found that holds
458 bullets and slugs tight. It had hammerhead type slug in it that
was pulled out and they wouldn't stay in tight. Sabot was a loose fit
in 20ga, made for 20ga, but small, so I shrunk the bottom rib,
fits perfect, super tight, in 24ga and 585HE. Fits real tight to give
good resistance for good ignition.

Here is another 24ga/585 sabot that holds .452" 45cal pistol
bullets. Made by Hornady for 58cal ML. With 250 gr bullet in 585
will go about mach 4.

Here is easy way to weight plastic stocks with hollow butts, use rubber
coated computer mouse balls, weight comes out perfect without being
too heavy if using that much lead.And coating keeps them quiet, and
we hold them in with piece dense foam under butt pad....Ed

 

[hubel585]

First AUS buffalo killed by 585HE. By Tankhunter with his Ruger #1.
If you use closeup on picture, you see loaded round on the buffs hide
next to the 585HE Ruger #1.... A nice heavy barreled gun..Ed

　
I put the 585 in a Savage 112, lots of room lengthwise, figuring out an
extractor is a problem, but then got a look at the savage 212, the 12 ga
one with big diameter bolt and locking lugs. Its locking lugs are bigger
than the lugs in a big PH bolt action. So one day will do one
on a Savage 212, and adjusting extractor to fit no problem...Ed

 

[benenglish]

Just out of curiosity, do you know of any source of 50-to-30 cal sabots? I don't care if the outer diameter is for .510 or .500 bores. TIA.

 

[hubel585]

No I don't. I Can find them for 50cal down to 44cal for

muzzleloaders and black powder cases guys use..ED

 

[hubel585]

Here is picture of 100 cases loaded with CEB solid nose bullets
and hollowpoints. This bullet is a turned solid with wide meplat
or wide hollowpoint. .

Here is picture of triball loads that fellows like for deer and hogs,
and just general tear em up fun, with using BPGS seal to improve
sealing under what are heavier loads. The balls are .600" and
315gr. each. The wadcup is a TUPRW123 that Precision sells.

　
Our 585 caliber is modern bolt action continuance of the 577 Nitro
Express rimmed case, that many big game hunters like, usually
set up in double rifles. It has an interesting history, from the old 24ga
size to 577NE, to 585 Nyati with G&A picture of Ross Seyfreid
shooting one in a Ruger #1 under recoil knocking his shooting glasses
off, to the Trex of internet fame knocking guys over with recoil,
to our 585HE the strongest yet.
The 577NE is an offshoot of 24 gauge caliber paper cases, only they went
eventially to brass cases. Back in the 1860-70s, starting first with short
cases and black powder, cases built like shotgun cases, called the
577 Snider, then going to coiled brass cases, still with black powder,
then on to drawn brass cases, called 577 BP Express. then to 3"
and other longer cases with smokeless. The Snider started out with a bullet
of .570" diameter and through the progression to the 577NE bullet
diameter ended up at .585". This general bore diameter of cartridge guns
and muzzle loaders, it is really interesting on how they developed
and were used by military and then hunters over the years. The Snider
was necked down to make the 577-450 , a military round used all
over the British Empire, by the tens of millions.
Bases of both 24ga and 577NE are about the same. Now we have made a
24ga FH, a slight regression to earlier times, by taking 577NE brass, and
reducing rim diameter to 24ga specs. Two minute job. And
stamp the caseheads 24 ga.
For shotgun upgrading in power and range, It is all about increasing
the power in easy to find brass cases, stronger actions, and finding
reasonable price rifled barrels. Same barrels we found for 585, work for 24ga.
The 577NE brass we make 24ga drawn cases from, for example are
about a third the cost of 600NE brass, or getting turned 24ga cases made.
We could use 24ga thin cases but they are a pain, expand way too much,
with slug loads which makes resizing without crumpling cases a problem.
Info about the power in types of guns normally set up with 24ga FH,
break actions, bolt shotguns,etc. In thin brass 24ga case, 440gr slug
goes 1500, with about 2000 ft lbs, that's in a 2.5" Magtech brass case.
Now using the better, heavier 3" brass we got, we can increase speed
to 1750 fps increasing energy 50%, going to 2000 fps about doubles
energy. And going to 2300 which good brass holds ok, in heavy barrel
gun, gets us near 2 1/2 times the energy. About 37-40,000 psi which the
actions hold in this smaller diameter case, compared to 12 gauge size.
So makes relatively smaller bore shotgun, 24ga, with 458WIN power.
.Perfect with Minie bullets. Perfect for deer and hogs, bear, etc.
Great for slug hunting in shotgun only areas. We mark barrels 24ga
and cases 24. A decent case that is complimentary to our 585HE....Ed
　

 

[hubel585]

Guys asking about using 585 CEB bullet in our 12ga super
sabot. Here is picture, We just took off the bottom band and couple
middle bands on the CEB and it fit perfect in our 12ga sabot,
which uses .575" slugs. Hollowpoint one pictured 700gr in the
sabot loaded in brass case. Can be used in plastic case with a
special made hollowed out long roll crimper.

Getting some more interest in our 585HE.
An application for our 585 HE is for guys with old military 14.5mm
PTRDs, to use our case with chamber insert. In many places 14.5
cases are scarce, real expensive, as well as most 14.5mm cases
being steel are not the easiest to resize/reload. Our case sizes
like regular cases and can be easily reloaded many times.
And a PTRD with almost a 5 foot long barrel could get 650gr
spitzer bullet to about same speed the 14.5mm gets a 900 gr using
3 times as much powder. About 3300 fps. Or get a 900gr at 2800.
Great possibilities for fun shooting. For tactical use in a place
where it would be useful to reload in the operations field, where
steel cases are scarce. 100 of our cases do over 2000 reloads.

I like Enfields to put our 585HEs in, for reasonable cost guns, the
actions once sporterized are one of the longest for long cases. .
Here is inexpensive way to fancy up the Enfield Bolt handle by
cutting the dogleg part of the old handle off and welding on
inexpensive contoured handles I found, one of which is like
Ruger 77 handle, the one on the right . Something even a novice
like me can do.....

A lot of guys are crazy about CEB bullets. Here are light 450gr
ones in our 24ga FH. That hollowpoint can range in weight 450gr
to 700gr depending on how much we cut off the back..
The 24ga FH brass case is nice complement to our 585HE,
for shotgun only deer hunters that want a .585" caliber,
and easy to find big bore bullets.... Ed

　
　

 

[Rebel]

It's fantastic this project is still going. I've always wanted a big game double rifle in some old black powder monster caliber like .375 H&H or .500/450 Nitro Express. I might change that to one of these instead.

 

[hubel585]

For lightweight plinking, deer hunting, etc, in 585HE as well as 24ga FH
here is picture of 58cal Hornady sabot that holds .451/.452" light
bullets 225 to 300 gr. A way to shoot targets economically. Low recoil
but a big bang and satisfaction. A 250 gr bullet would go about
mach 4 with a top load..

Here is what 585 bull barrel, target blank looks like, 1 5/8" OD and 32" long.
It'll go in heavy action of some kind. 4th one from the left. The one in yellow
sleave on top, is a heavy contoured one with muzzle of .980". we got a
bunch of them and so does McGowen.

　
Here is picture, nice cast bullet I like for the 585HE and 24ga FH.
It is .585" diameter and 650 gr and these particular ones are a
hard lead alloy, plus they've been heatreated. They are about as
hard as copper jacketed softs pivtured. These in .575'' size would
work in our 12ga sabot..

But to penetrate good and do great damage to game or target they
can be fairly soft lead and hollowbase like Minie Bullets. Here is picture
of timber drilled through with .585 soft lead Minie from 585HE.
Picture is the back of 6x6 timbers where Minie bullets came out.

Guys experimenting with multiple ball loads in 12ga wadcups, here is a
way to keep them together group wise.Ed
　

 

[hubel585]

Here is picture of our NEF 12ga FH with Hogue Compstock. It has the
recoiling cam and springs in the hollow butt plus some weght,

Here is a variety of slugs and bullets that fit in the 12ga dangerous
game slug, lock on sabot. BPI sells that DG slug.
.

There is couple 585 videos on Swann Gunsmithing's Facebook site;
Of our 585HE in first Ruger #1, that was done in Australia.It was set up
for the poster Tankhunter on the AR big bore forums. That gun killed the
first AUS buff, killed by a 585HE, that I posted picture of above. You can
go direct to the page and click on the videos to watch the test firings..
https://www.facebook.com/swanbarrels/videos
　
Here is picture our 585HE in a Montana PH action in a MPI stock, with the
style of a CZ stock and metal will be finished with a Gun Kote finish.
　

　
Here is picture of a 585HE we did in a Mauser 98 as a
singleshot test gun. We used a composite stock we
adapted to fit action. Weighted to 12 lbs.
Enfield in back, you can see it is longer.

And speaking of singleshots a fellow in the Yukon is
just finishing up one in a Ruger #1.And the 24hr Campfire
forum has over a million views of this thread, ..ED

 

[hubel585]

The 12ga FH isn't the first wildcat case built on BMG brass, it was preceded by
target rounds like the necked down 338 Talbot, the cut off 700 DKT for big game,
necked down to .416 and . 458, and more, but the following one was way
before them, in my favorite rifle caliber, for .585" bullets.
One of first modern era 585 caliber wildcats, since WW2, the 575 Miller-Greiss Magnum,
was first mentioned in the fifties, It was made from BMG brass shortened to 2.70" long
and necked up from 50 cal to .585". But actually if cut off first, it would be annealed, necked
down to hold 585 bullet. Fairly sharp shoulder.
They rebated the rim quite a ways down to .618" to maybe fit 98 Mauser bolt.
Maybe used a special hogged out, reworked action. Listed as
shooting 750gr bullet about 2400 fps. It holds about 150gr of ball powder under
a 750 gr bullet, maybe little less than 3" 50cal spotter case, where our 585HE holds
180gr under a 750gr'.
We made one for experimenting on a full length BMG case.With rim left same as the base
and would need a BMG or PH sized bolt and action. I'm glad to be a big bore wildcatter,
and happy to be in the company of big bore nuts, old and new. Years ago when guys did
big wildcats on BMGs, they took what was available, full length BMGs to rework, and but
maybe back then they could have used the 3" BMG spotter case, by shortening the neck,
if they could have found couple barrels full.
But it takes a lot of work to reform and shorten cases that much like M&G, with the multiple dies,
multiple annealings, and case trimming and extreme reworking of regular rifle actions,
which is why I like our 585 case, simple and straight, any regular, long bolt action, or
falling blocks, break actions, etc, a 585 good for dozen or more heavy loadings,
and moderate loads, last forever..
For our 585HE , made it a size, actually new belted size, to fit regular size, long bolt guns,
(not BMG actions)that didn't have to be used from tripod so to speak, and could be put in a favorite
gun of many, the Ruger #1, other falling blocks, without taking metal out of the feed trough.
To get the same and/or more powder space as a cut back, really shortened, BMG case, like M&G,
wildcatted to 585, or other short cases, we made longer case and worked with guys
with a group buy, to get a factory run made. A miracle. We thank all gun nuts for the help.
Here is picture from the great site, cartridgecollector dot net, of the M&G Mag .Ed

 

[hubel585]

Guys asking about using 24ga Magtech brass in our
24ga FH. Brass is 1/2" short, so thin that if left out to dimensions
to fit 24ga shotgun chamber it won't hold a slug. And if
swaged down to hold slug it is real loose in the chamber.
Our cases are 3" and thicker, better for slugs.

Probably first 375 caliber cartridge made from 585HE necked down, the 375 Warlord.
Guy did a real nice job, with what looks similiar to a Weatherby style shoulder.
Kinda outdoes Weatherby & Cheytac. We have cases with no headstamps for wildcatters.
First notice of the case sent to me today off of a guys facebook.
　
[1Another fellow is planning on shortening the 585HE to maybe 2.4", for use Marlins and Henrys,
and other leverguns, redoing their 45-70s. With the belt they will have good headspace control.
Without a rim that takes up space in a levergun action, say like our rimmed 24ga FH, a 585 bore,
but which is perfect with that rim for break actions like our 24ga FH in a Magtech...Ed

 

[hubel585]

Sorry to be away so long, health, getting old, and interruptions.
Here is picture of a lightweight Barnes bullet in 24ga FH.
Guys cut the back off of 750gr bullet off to get 500gr weight.

Here is picture 58 cal Minie slug that's little long on the side for our 12ga
sabot, with the front of the slug above the grooves swaged to fit in
sabot. The swaged front third of the slug fits next to the internal ridge in
sabot and the sabot doesn't bulge out.Just run front into a die
and punch it back out.
　

And some info about 12ga FH and other hopped up shotgun slug loads,
You know we like to use the rifle, IE slower than shotgun, powders.
We like to use IMR 4759 for some loads and RE17 for others where
we have room for larger charges. Those two powders are ignited ok in large
diameter cases like 12ga, 10ga, 16ga, etc, without needing BMG primers.
But we have always been looking for easy to ignite powders of the RE17
type, when cold, that has a speed between IMR 4759 and the RE17.
RE17 uses different process to put the deterrents in the powder to control
speeds, which allows much easier ignition, compared to big majority of rifle
powders with all the deterrent on the outside.
There are some out there made by Nitrochemie Switzerland, who makes
RE17, RE26, RE33, etc, for Alliant. It's the ' RELOAD SWISS' brand available
for those in UK and Europe, They are called RS 40, about same speed
as RE12, RS 50 & 52, same speed as RE15, RE60 & 62 same as RE17.
Also one ' Vihta Vouri ' powder called TR140 available over there,
that Nitrochemie made..
Many guys can't get IMR 4759 anymore, some can't get RE17.
I'd like to get some of RS 40-50-52 powders or V V TR140
into the states, would really be great help for hairy slug load work. Ed
　
　

 

[hubel585]

Here is picture of 375 Warlord next to our 585 case he made it from.
He is going to make couple later necked down to 416, and 458.
There is another guy working on doing one necked down to 357 wildcat.

Here is a picture of our poster Biebs on AR, 585 HE, in a MPI stock.
He used a big Enfield action, with a fancy jeweled bolt.

We found couple other big actions for our 585, that can even feed really
long overall length loaded cases, like 4.5" long or more, if you are
using long pointed bullets for real long range target and hunting work.
One is Lawton 8000 Cheytac action, and the other is Stiller Cheytac actions
made similiar, justa newer version. Both actions come in 1.45" diameter
and a 1.60" diameter recievers.
And Vestals Gunsmithing in Virginia does great work, decent prices, has
these actions and will build you fancy 585 HEs. .. He has, working with
another guys mag box setup, setup an extra long, good working, single
stack, center feed, magazine..He has our 585 HE reamer on hand, we have
barrels, cases, and reloading dies..Ed

 

[hubel585]

Here is couple different setups our guys checking for our 585HE
in a long, Lawton Cheytac action. First laminated thumbhole stock.
Second in a Hogue Compstock. The action can mount a scope rail
like shown on the table in 1st picture or a receiver sight in 2nd picture.
The scope rail is a piccatiny,. if you need long range work.

The stocks used were wide ones for REM long actions, just add recoil
block ahead of recoil inleting for the longer action, drill new screw hole
Open the stock forward to original bolt hole for longer cases and mag.


About Enfields for our case, one of my favorites, Some don't like the
sporterizing, welding bottom metal straight. Many think straightening
is a huge job needing special jigs, etc, Not really, just use one for a jig
with a bolt, to weld on the straight extension, Do top weld, then cut old
extension that is under off with a thin cutting wheel, then weld bottom.
When we bolt the short piece on the one we are straightening, we grind
the short slant off so the added piece lays on there flat.
The one you cut off can be used as the top extension for the next one!!!
Just keep on building...Ed

 

[hubel585]

Here we kill two birds with one stone so to speak,


Best case sizer is the MEC Collet Super Sizer and it can double
as a case holder when we roll crimp. Much better hold than
the ones made to hold cases for crimping, that cost a lot.
Save cost of a holder, plus have best sizer around

 

[hubel585]

Here is a fancy stocked 24ga FH built on a NEF, built by
a guy in Canada. Its straight back, high comb
stock, handles recoil great.Neat looking work... Ed

More about 585 BB case for lever guns, pistols, AR Uppers,
Work in 71s, later 1886s, Henry steel frames made for 45-70.
One guy is putting one in single shot action set up with
Contender style pistol grip for testing in long rifle barrel,
to simulate pistol recoil..Be very brisk recoil in a case
that holds 110 gr powder under a light Minie bullet
Maybe work in a Rossi Judge with heavy barrel.
Or rolling block rifles and pistols...Gonna try one in 1887.
Got first one in one of our guys Greener GP.


In some ways big bore shotguns and rifles are sexy.
By looking at the shape of the fire and smoke cloud....
Thanks for picture, to the great NitroExpress Forums site.

Here is picture of another neat sporterizing deal for Enfields.
On those without rear bridge pocket welded up, we just mill down
and shape it so debth of the pocket matches bottom section of
weaver rail and screw or epoxy it in. Shape to drive in hole tight.
Can use as a rear scope ring mount or mount for peep sight
like a compact UTG sight...Ed